Fortis Coat 823 HS High Solids Epoxy Floor Coating
Fortis Coat 823 HS is a durable epoxy floor coating for warehouses, factories, workshops, garages and commercial concrete floors. Designed for demanding traffic and wear, it provides a hard-wearing gloss finish and can be used for solid-colour or decorative flake flooring systems.
Information
Fortis Coat 823 HS is a 95% solids, two-component high-build epoxy formulated for industrial, commercial and residential concrete flooring where durability, film build and long-term protection are required.
The high-solids formulation produces a hard-wearing seamless finish with excellent resistance to abrasion, vehicle and pedestrian traffic, oils and common chemicals. It provides greater film build than lower-solids roll-applied coatings while remaining practical to apply by roller.
Coat 823 HS is suitable for warehouses, factories, workshops, manufacturing areas, garages and commercial floors. It can be used as a solid-colour flooring system or as the base coat for decorative flake and slip-resistant systems.
On suitable properly prepared concrete, Coat 823 HS can be self-priming. Fortis 823 Prime can be used where rapid recoating and additional penetration are required, while Fortis 820 Prime is suited to poor, porous or difficult concrete where high adhesion and substrate consolidation are important.
For self-levelling or substantially higher-build flooring, consider Fortis Coat 824 SL. Where low odour and water-based application are priorities, Fortis AquaCoat™ provides an alternative epoxy flooring system.
Material
95% Solids Two-Component Epoxy
Advantages
- 95% solids epoxy formulation
- High-build roll-applied coating
- Hard-wearing seamless gloss finish
- Excellent adhesion to properly prepared concrete
- Excellent abrasion and wear resistance
- Resistant to vehicle and pedestrian traffic
- Good resistance to oils and common chemicals
- Suitable for industrial and commercial floors
- Suitable for garage flooring
- Can be self-priming on suitable prepared concrete
- Ideal base coat for decorative flake systems
- Can be made slip resistant with suitable aggregate
- Available in clear and coloured finishes
Product Application
FORTIS Coat 823 HS is suitable for warehouses, factories, workshops, garages, plant rooms and commercial concrete floors requiring a durable, high-build epoxy finish. It can also be used in decorative flake and slip-resistant flooring systems.
Apply to clean, sound and mechanically prepared concrete. Diamond grinding is recommended to remove laitance, contamination and weak surface material while creating a suitable profile for adhesion.
Premix Parts A and B separately. Combine 3 parts resin (Part A) with 1 part hardener (Part B) by volume. Mix thoroughly at low speed using a suitable mechanical mixer until homogeneous.
Pour the mixed coating onto the prepared floor in ribbons and distribute evenly using an epoxy-compatible roller. Maintain a consistent wet edge and avoid excessive rolling as the coating begins to cure. Typical coverage is 5–7 m²/L per coat, depending on substrate condition and application requirements.
Primer selection: On sound, properly prepared concrete, Coat 823 HS can be diluted with FORTIS Solv X for use as a primer. For faster recoating, use FORTIS Prime 823. Where concrete is substandard or potentially exposed to moisture, FORTIS Primer 820 is preferred. Follow the relevant technical data sheets for dilution and recoating requirements.
For decorative flake systems, broadcast flake into the wet base coat. Where additional surface grip is required, incorporate or broadcast FORTIS Non-Slip Additive according to the required texture.
For primer guidance, read How to Choose an Epoxy Floor Primer. Refer to the current Coat 823 HS Technical Data Sheet for full application and curing instructions.
Surfaces
Suitable Surfaces
Coat 823 HS is suitable for mechanically prepared concrete, appropriately primed concrete and compatible existing epoxy flooring systems.
Concrete must be clean, sound and free from dust, laitance, oil, grease, curing compounds and other contaminants that may affect adhesion. Diamond grinding is the preferred preparation method.
New concrete should normally be cured for at least 28 days before coating. Porous or difficult concrete may require Fortis 820 Prime or 823 Prime depending on substrate condition and flooring requirements.
Existing compatible epoxy coatings must be firmly bonded, cleaned and mechanically abraded. Test adhesion before proceeding.
Where rising damp, hydrostatic pressure or significant moisture transmission is present, investigate the substrate before coating and use an appropriate HydroFort™ epoxy vapour barrier where required.
Specifications
| Specification | Value |
|---|---|
| Foot traffic | Approximately 24 hours |
| Finish | Gloss |
| Number of Coats: | 1–2 depending on system requirements |
| Tack free | Approximately 6 hours |
| Recoat Time | 8–24 hours |
| Coverage | Approximately 5–7 m²/L per coat |
| Film Thickness | Approximately 150 μm per coat |
| Working Time | 30-60 minutes |
| Mix ratio | 3 Parts A : 1 Part B by volume |
| Volume Solids | 95% |
| Product Type | Two-component high-solids epoxy |
Pack Sizes
4 L Kit, 16 L Kit
Available Colours
Fortis Coat 823 HS FAQs
What is Fortis Coat 823 HS?
Coat 823 HS is a 95% solids, high-build epoxy floor coating for industrial, commercial and residential concrete floors.
Where can Coat 823 HS be used?
It is suitable for warehouses, factories, workshops, garages, manufacturing areas and commercial concrete floors.
Does Coat 823 HS require a primer?
It can be self-priming on suitable prepared concrete. Fortis 820 Prime or 823 Prime may be used where additional adhesion, penetration or substrate consolidation is required.
Can decorative flake be used with Coat 823 HS?
Yes. Decorative flake can be broadcast into the wet coating to create a decorative epoxy flooring system.
How is Coat 823 HS different from AquaCoat® and Aquepoxy®?
Coat 823 HS provides greater film build and is designed for more chemically demanding floors. AquaCoat® and Aquepoxy® are both water-based and suited where low odour and easy application are priorities.
How is Coat 823 HS different from Coat 824 SL?
Coat 823 HS is a roll-applied high-build epoxy. Coat 824 SL is a self-levelling system for greater build and floor levelling.
How long before the floor can be walked on?
Light foot traffic is typically possible after approximately 24 hours under suitable curing conditions.
Does Fortis Coat 823 HS require a separate primer?
Not always. Coat 823 HS can be diluted with Solv X to act as a primer on suitably prepared concrete. For faster recoating, use Fortis Prime 823. For substandard concrete or surfaces potentially exposed to moisture, Fortis Primer 820 is recommended.
Downloads
Technical Datasheets
Fortis Coat 823 HS - Technical Data Sheet
Safety Datasheets
Fortis Coat 823 HS Pt.B- Safety Data Sheet
Fortis Coat 823 HS Pt.A- Safety Data Sheet
Resources
Epoxy vs Polyurethane vs Polyaspartic Floor Coatings
Water-Based vs High-Solids Epoxy: Which Is Better?
How to Choose an Epoxy Floor Primer for Concrete
How Many Coats Does an Epoxy Floor Need?
How to Add Slip Resistance to an Epoxy Floor
How Temperature Affects Floor Coating Application
Why Do Bubbles and Pinholes Form in Epoxy Flooring?
Why Does Floor Coating Reject or Form Fish Eyes?
Why Does Epoxy Flooring Delaminate? Causes, Prevention & Repair
Why Do Car Tyres Stain Epoxy Floors?