AquaCoat® Water-Based Epoxy Floor Coating
Fortis AquaCoat® is a two-component, ultra-low VOC water-based epoxy floor coating manufactured in Melbourne and supplied Australia-wide. Designed for garages, workshops and light to medium-duty commercial concrete floors, AquaCoat® provides a durable, low-odour finish and can be used as both a primer and topcoat on suitably prepared concrete. Buy online or contact Fortis for technical advice and trade supply.
Information
Water-Based Epoxy Floor Coating for Concrete
Fortis AquaCoat® is a high-solids, two-component water-based epoxy coating designed for internal concrete floors where low odour, ultra-low VOC and easy application are important.
AquaCoat® provides a durable protective finish for residential garages, workshops, car parks, offices, schools, healthcare facilities, food service areas and light to medium-duty commercial floors.
Its water-based formulation makes it particularly suitable for internal environments where solvent odours need to be minimised. AquaCoat® can be used as both a priming coat and finish coat on correctly prepared concrete.
Why Choose AquaCoat®?
Ultra-low VOC and low-odour formulation.
Two-component water-based epoxy with water clean-up.
Suitable as both a primer and finish coat.
Excellent adhesion to properly prepared concrete.
Suitable for appropriately prepared damp concrete.
High-solids formulation with durable film build.
Long working time and easy roller application.
Suitable for pedestrian and light to medium vehicle traffic.
Available in 4 L and 12 L kits.
Where Can AquaCoat® Be Used?
Garage Floor Epoxy Paint
AquaCoat® is suitable for residential garages and home workshops requiring a durable, low-odour epoxy floor finish. The coating is designed for correctly prepared concrete exposed to pedestrian and light to medium vehicle traffic.
Commercial and Workshop Floors
AquaCoat® can be used in workshops, offices, schools, healthcare facilities and light to medium-duty commercial premises where low-odour application is important.
Car Parks and Internal Concrete Floors
AquaCoat® provides a protective epoxy finish for suitable internal car parks and concrete floors. For larger commercial projects or more demanding service conditions, consider Aquepoxy® Water-Based Epoxy or contact Fortis for a flooring specification.
Does AquaCoat® Need a Primer?
AquaCoat® can be used as its own priming coat on properly prepared concrete. Where specified, the first coat may be diluted with 10–15% water to assist penetration and adhesion. Subsequent coats are applied undiluted.
For poor or difficult concrete, additional preparation or a specialist primer may be required. Refer to the Fortis Epoxy Floor Primer Selection Guide or contact our technical team.
How to Apply AquaCoat®
Concrete must be clean, sound and mechanically prepared before coating. Diamond grinding is recommended to remove laitance, contamination and weak surface material while providing a suitable surface profile for adhesion.
Apply 2–3 coats as required. Typical coverage is 5–7 m²/L per coat, with a recoat interval of 8–24 hours under suitable conditions.
Allow approximately 24 hours before light foot traffic and 7 days for final cure. Application and curing times depend on temperature, humidity and ventilation. Follow the current AquaCoat® Technical Data Sheet.
AquaCoat® or Aquepoxy®?
Fortis supplies two established water-based epoxy coating systems for different project requirements.
Feature | AquaCoat® | Aquepoxy® |
|---|---|---|
Coating type | Two-component water-based epoxy | Two-component water-based epoxy |
Typical applications | Garages, workshops and light to medium-duty commercial floors | Car parks, factories, warehouses, commercial complexes and garages |
Main advantage | Ultra-low VOC, low odour and self-priming capability | Established 25-year history in commercial flooring |
Typical coverage | 5–7 m²/L per coat | 8–10 m²/L first coat; 10–12 m²/L second coat |
Pack sizes | 4 L and 12 L kits | 25 L kit |
Product information |
For high-build industrial flooring, consider Fortis Coat 823 HS. For a smooth, self-levelling floor, see Fortis Coat 824 SL.
Buy Water-Based Epoxy Floor Coating in Melbourne
Fortis Adhesives & Coatings manufactures and supplies AquaCoat® from Dandenong South, Melbourne, with delivery available throughout Australia.
AquaCoat® is available in 4 L and 12 L kits. Customers can buy AquaCoat® online or contact Fortis for trade quantities, colour selection and technical advice.
Water-Based Epoxy Technical Resources
For other flooring systems, view the complete Fortis Epoxy Floor Coatings range.
Material
Two-Component Water-based Epoxy
Advantages
- Ultra-low VOC and low odour
- Water-based two-component epoxy
- Self-priming on properly prepared concrete
- Can be used as primer and finish coat
- Suitable for appropriately prepared damp concrete
- Excellent adhesion to prepared concrete
- High-solids formulation
- Long working time for easier application
- Easy roller application
- Water-thinnable priming coat
- Water clean-up
- Suitable for pedestrian and light to medium vehicle traffic
- Ideal for internal and occupied environments
Product Application
Typical Applications
AquaCoat® is suitable for garages, workshops, carparks, offices, schools, healthcare facilities, food service areas and light to medium-duty commercial floors. Its low-odour water-based formulation makes it particularly suitable for internal and occupied environments.
Application
Concrete must be clean, sound and mechanically prepared before coating. Diamond grinding is recommended to remove laitance, contamination and weak surface material while providing a suitable profile for adhesion.
AquaCoat® can be used as its own priming coat. Where specified, dilute the first coat with 10–15% water to assist penetration into properly prepared concrete. Apply subsequent coats undiluted at the recommended coverage rate.
Apply evenly by roller, maintaining a consistent wet edge and avoiding excessive film build or pooling.
Apply 2–3 coats as required. Typical coverage is approximately 7–10 m²/L per coat with a recoat interval of 8–24 hours.
Allow approximately 24 hours before foot traffic and 7 days for final cure under suitable conditions. Refer to the current AquaCoat® Technical Data Sheet for complete mixing, application and curing requirements.
For areas requiring additional surface grip, Fortis Non-Slip Additive can be incorporated into AquaCoat® to create a more textured, slip-resistant floor finish. Select the addition rate according to the required surface texture and service environment.
Surfaces
Suitable Surfaces
AquaCoat® is suitable for properly prepared internal concrete floors, including new and existing concrete and compatible existing coating systems.
Concrete must be clean, sound and free from dust, laitance, oil, grease, curing compounds and other contaminants that may affect adhesion. Diamond grinding is the preferred preparation method.
New concrete should normally be cured for at least 28 days before coating unless otherwise approved by Fortis technical staff.
Existing compatible coatings must be sound, clean and mechanically abraded. Test adhesion on a small area before proceeding.
AquaCoat® can be applied to suitably prepared damp concrete. Where rising damp, hydrostatic pressure or significant moisture transmission is suspected, investigate the substrate before coating and use an appropriate HydroFort® vapour barrier where required.
Specifications
| Specification | Value |
|---|---|
| Number of Coats | 2–3 coats |
| Final Cure | Approximately 7 days |
| Foot traffic | Approximately 24 hours |
| Tack Free | Approximately 4–8 hours |
| Recoat Time | 8–24 hours |
| Coverage | Approximately 7- 10 m²/L per coat |
| Film Thickness | Approximately 150 μm per coat |
| Working Time | 30–60 minutes |
| Product Type | Two-component water-based epoxy floor coating |
Pack Sizes
4 L and 12 L kits
Available Colours
AquaCoat® Water-based FAQs
What is AquaCoat®?
AquaCoat® is a two-component, high-solids water-based epoxy floor coating manufactured by Fortis. It provides a durable, low-odour, ultra-low VOC finish for suitable interior concrete floors.
Where can I buy AquaCoat® in Australia?
AquaCoat® can be purchased directly through the Fortis AquaCoat® online store listing, with supply available throughout Australia.
Does AquaCoat® require a separate primer?
Not normally on sound, correctly prepared concrete. AquaCoat® can be used as its own priming coat, with dilution where specified. For difficult substrates or significant moisture concerns, refer to the epoxy primer selection guide.
Can AquaCoat® be applied to damp concrete?
AquaCoat® can be applied to suitably prepared damp concrete within the manufacturer's requirements. It is not a substitute for a moisture vapour barrier where rising damp or significant moisture transmission is present.
Can AquaCoat® be used on garage floors?
Yes. AquaCoat® is suitable for prepared garage floors and light to medium-duty commercial concrete floors. For a higher-build system, consider Fortis Coat 823 HS.
How many coats of AquaCoat® are required?
Typically two to three coats are recommended, depending on the substrate and finish. See the Fortis epoxy coating guide for general coating system information.
What is the coverage of AquaCoat®?
Typical coverage is approximately 5–7 m²/L per coat. Actual coverage depends on surface porosity, texture and application method.
What is the difference between AquaCoat® and Aquepoxy®?
Both are water-based epoxy floor coatings. AquaCoat® is an ultra-low VOC, high-solids system for suitable interior floors, while Aquepoxy® has an established history in car parks, factories and large commercial flooring projects.
What is the difference between AquaCoat® and Fortis Coat 823 HS?
AquaCoat® is a low-odour water-based epoxy for suitable interior floors. Fortis Coat 823 HS is a high-solids epoxy providing greater film build for more demanding industrial and commercial applications.
Can AquaCoat® be applied over existing epoxy?
Yes, where the existing epoxy is compatible, firmly bonded, cleaned and mechanically prepared. Complete an adhesion test before recoating.
Downloads
Technical Datasheets
AquaCoat™ - Technical Data Sheet
Safety Datasheets
AquaCoat™ Pt.B- Safety Data Sheet
AquaCoat™ Pt.A- Safety Data Sheet