Premium Lithium Concrete Densifier

Concrete Shield™ Premium Lithium Densifier is a high-performance concrete densifier for premium polished concrete floors. It hardens and densifies the surface while supporting a refined polished finish, making it ideal for residential interiors, retail floors, showrooms and decorative concrete.

Information

Concrete Shield™ Premium Lithium Densifier is a water-based lithium silicate treatment with penetrating additives, designed for premium polished concrete floors. It reacts within the concrete to increase surface hardness and density, improve abrasion resistance and reduce dusting.

Suitable for residential, retail, showroom and commercial floors, it supports a dense, durable surface and a refined polished finish on properly prepared new or existing concrete.

Premium Lithium vs Potassium/Lithium Densifier

Premium Lithium is designed for high-quality polished concrete where surface refinement and polishing performance are priorities. Potassium/Lithium Densifier is an economical alternative for general hardening, dustproofing and larger floor areas.

Both products densify concrete rather than forming a surface film. Selection depends on slab condition, desired finish and polishing requirements.

Concrete Shield™ Polishing System

Premium Lithium Densifier is used during grinding and polishing. Grout 1000 can help fill pinholes and minor surface imperfections during preparation.

Following densification and polishing, Natural Look Enhancer or a compatible Wet Look Enhancer may be used for additional appearance enhancement.

See our polished concrete technical guides for product selection and application advice.

Material

Lithium Silicate Concrete Densifier with Penetrating Additives

Advantages


  • Premium lithium silicate concrete densifier
  • Water-based penetrating formulation
  • Hardens and densifies concrete surfaces
  • Improves abrasion and wear resistance
  • Helps reduce concrete surface dusting
  • Designed for polished concrete systems
  • Assists development of a high-quality polished finish
  • Suitable for progressive grinding and polishing
  • Suitable for new and existing concrete
  • Colourless and odourless
  • Suitable for interior and exterior concrete
  • Ideal for residential, commercial and decorative polished floors

Product Application

Polished Concrete: Apply by spray or squeegee between grinding stages. For best results, apply once early and again later in the grinding process. Do not apply during final polishing.

Surface Hardening: Apply one undiluted coat at approximately 5–8 m²/L depending on porosity. Scrub into the surface for at least 30 minutes until slippery. Lightly mist with water and continue working for 10–20 minutes. Remove excess with a squeegee and wet vacuum. Do not allow material to pond or dry on the surface.

Porous or rough concrete may require a second application after 2–4 hours. Allow approximately 4–6 hours before returning the floor to service.

New Concrete: Apply evenly, preferably 7–14 days after placement. Avoid application to concrete less than 3 days old, as excess moisture may reduce penetration.

During grinding, fill pinholes and surface imperfections with Concrete Shield™ Grout 1000. After densification and polishing, use Natural Look Enhancer for a natural appearance or Wet Look Enhancer for deeper colour enhancement.

Surfaces

Suitable for new and existing concrete surfaces used in polished concrete systems.

Not suitable for natural stone. Do not apply over concrete previously treated with curing compounds or membrane-forming sealers unless they have been completely removed.

Concrete Shield™ Premium Lithium Densifier will not restore badly deteriorated or disintegrating concrete and may not perform effectively on lightweight, extremely porous or severely worn concrete.

Specifications

Specification Value
Water-Based Yes
Moisture loss Reduced by a minimum of 85% during initial 24 hrs
Abrasion resistance >30% (Taber abrader wheel H22/1000g/500 cycles)
Appearance Colourless, odourless liquid

Pack Sizes

15L

Premium Lithium FAQs

What does a lithium concrete densifier do?

Lithium densifier penetrates concrete and reacts within the surface to increase hardness, improve abrasion resistance and reduce dusting.

Why use lithium densifier for polished concrete?

Lithium silicate is well suited to polished concrete systems, helping create a hard, dense surface capable of developing a high-quality polished finish.

What is Premium Lithium Concrete Densifier?

Concrete Shield™ Premium Lithium Densifier is a water-based lithium silicate treatment with penetrating additives for hardening and densifying concrete.

What is the difference between lithium and potassium/lithium densifier?

Premium Lithium is designed for high-quality polished concrete systems. Potassium/Lithium Densifier is an economical choice for general hardening, dustproofing and larger concrete floors.

When is lithium densifier applied during polishing?

Apply during the grinding process. For best results, apply once early and again later in the grinding sequence. Do not apply during the final polishing stage.

Can it be used on existing concrete?

Yes. It can be used on suitable new or existing concrete that is clean, prepared and able to absorb the densifier.

Is lithium densifier a concrete sealer?

It is a densifier that reacts within concrete to increase surface density and hardness rather than forming a conventional surface coating. 

How much lithium densifier do I need?

Typical coverage is approximately 5–8 m²/L depending on concrete porosity and condition.

Can it be used indoors and outdoors?

Yes. It is suitable for interior and exterior concrete surfaces

Premium Lithium Concrete Densifier

Concrete polished floor finished with Concrete Shield™ Premium Lithium Densifier