Fortis AD525 Polyurea Joint & Crack Repair
Fortis AD525 is a rapid-setting, self-levelling, two-component polyurea joint filler for horizontal concrete control joints and suitable non-structural cracks. Designed for heavy-traffic and freezer applications, it supports joint edges while accommodating limited movement. Not suitable for expansion joints or damp substrates.
Information
Fortis AD525 is a two-component polyurea hybrid for filling control joints, construction saw joints and suitable non-structural cracks in horizontal concrete. It suits warehouses, factories, workshops and specified freezer-floor applications exposed to demanding wheeled traffic.
The 100% solids formulation combines Shore A hardness of 85–90 with limited movement accommodation. Dispense using compatible 1:1 equipment and the correct static mixer. Do not use in expansion joints, damp conditions or joints subject to hydrostatic pressure or extreme movement.
For selection advice, read our joint filler and crack repair guide or contact Fortis.
Material
Two-Component Rapid-Curing Polyurea Elastomer
Advantages
Rapid-setting, two-component polyurea hybrid.
Self-levelling for horizontal concrete joints.
Supports joint edges under heavy wheeled traffic.
100% solids with low shrinkage.
Accommodates limited joint movement.
Suitable for specified freezer-floor applications.
600 mL dual cartridge for controlled dispensing.
Certifications
Conforms to ACI 302.1R – Guide for Concrete Floor and Slab Construction (Joint Materials).
Product Application
Joint faces must be sound, completely dry and free from dust, oil, loose concrete and existing filler. Mechanically prepare where necessary and vacuum thoroughly. Confirm concrete age, joint dimensions and installation conditions against the current TDS.
Use compatible 1:1 dispensing equipment. Equalise component flow before attaching the correct static mixer, then purge until the mixture is uniform. Fill from the bottom upwards without trapping air, slightly overfill and trim flush once sufficiently cured.
Setting and trimming times depend on conditions. Confirm readiness before reopening to traffic. Test adhesion before applying a coating over AD525. Do not use on damp substrates, in expansion joints or where hydrostatic pressure or extreme movement is present.
Surfaces
Suitable for prepared horizontal concrete control joints, construction saw joints and stable, non-structural cracks in industrial, warehouse, workshop and specified freezer floors.
Not a structural crack-repair resin or a replacement for rebuilding severely spalled joint edges. Substrates must be completely dry. AD525 may discolour under UV exposure; assess exterior applications for thermal movement and appearance requirements.
Specifications
| Specification | Value |
|---|---|
| Joint movement | 10–15% of installed width, subject to joint design and service conditions |
| Elongation | Greater than 200% |
| Hardness | Shore A 85–90 |
| Tack-free time | Approximately 10–15 minutes |
| Pot life | Approximately 4 minutes — 100 g quantity |
| Mixed consistency | Self-levelling |
| Solids | 100% |
| Colour | Grey |
| Dispensing ratio | 1:1 |
| Product type | Two-component polyurea hybrid |
Pack Sizes
600 mL dual-component cartridge
Polyurea Joint & Crack FAQs
What is AD525 used for?
Filling horizontal concrete control joints, construction saw joints and suitable non-structural cracks.
Is it suitable for warehouses and freezers?
Yes, for specified applications where substrate, traffic and installation conditions meet the TDS requirements.
Can AD525 be used in expansion joints?
No. It is not intended for expansion joints or extreme movement.
Can it be applied to damp concrete?
No. The substrate must be completely dry. Do not use where hydrostatic pressure is present.
Can it repair structural cracks or missing concrete?
No. Structural cracking and severely spalled joint edges require assessment and an appropriate repair system.
Can AD525 be coated over?
Test adhesion of the proposed coating to cured AD525 before proceeding.
Does 200% elongation mean 200% joint movement?
No. Elongation and allowable installed joint movement are different properties.
When can traffic resume?
Confirm sufficient cure for the intended traffic and conditions. Tack-free time alone does not establish readiness for service.
Downloads
Technical Datasheets
Fortis AD525 Technical Data Sheet
Safety Datasheets
Fortis AD525 Safety Data Sheet AUS GHS Pt B
Fortis AD525 Safety Data Sheet AUS GHS Pt A
Resources
Polyurea Joint Fillers, Concrete Crack Repairs & Expansion Joints — Choosing the Right Material